Skip to content
surmeshGet a quote

Sheet metal forming engineering

Behind every surface, there is a mesh.

Surmesh provides end-to-end engineering for sheet metal forming dies: feasibility, simulation, method planning, die face design and springback compensation.

Simulation with finite element software, design with 3D CAD software.

From coil to car

The journey of one sheet metal part

  1. 01

    Coil

    Every part starts as a flat strip.

  2. 02

    Blanking

    The blank outline is cut from the strip.

  3. 03

    Drawing

    The binder holds the sheet; the sheet is drawn over the punch.

  4. 04

    Simulation

    Thinning, FLD and wrinkling are seen before any die steel is cut.

  5. 05

    Trimming and piercing

    Excess sheet is cut along the trim line, holes are pierced.

  6. 06

    Flanging and restrike

    Flanges close, the part springs back; the die face is compensated.

  7. 07

    Assembly

    The part takes its place in the body in white. The mesh dissolves into a Class-A surface.

01 — Services

Before any die steel is cut

Every engineering step of a sheet metal forming die, from part data to tryout.

  • 01

    Forming feasibility and simulation

    Thinning, split and wrinkling risks are assessed on the FLD.

  • 02

    Springback analysis and compensation

    Deviation is measured, the die face is corrected in the opposite direction, the result is verified again.

  • 03

    Process and method planning

    Operation sequence for transfer and progressive press lines.

  • 04

    Die face and Class-A surfacing

    Draw die surfaces with binder, addendum and drawbeads.

  • 05

    Die cost estimation

    Cost forecast per operation, based on the method plan.

  • 06

    Trim line and blank development

    Trim line development and edge crack risk assessment.

02 — How we work

From CAD data to report

  1. 01

    CAD data

    Part geometry, material and thickness are received. Draw direction and critical areas are identified.

    Output: Input checklist

  2. 02

    Feasibility

    The part is assessed quickly in one step: split, wrinkling and undercut risks are flagged.

    Output: Feasibility note

  3. 03

    Method plan

    Operation sequence, press line and the task of each operation are defined.

    Output: Method plan

  4. 04

    Simulation loops

    Binder, addendum and drawbeads are refined until results are within acceptance limits.

    Output: Die face

  5. 05

    Compensation

    Springback is calculated, the die face is corrected in the opposite direction and the result is verified again.

    Output: Compensated surface

  6. 06

    Report

    Results, remaining risks and recommendations for tryout are documented.

    Output: Simulation report

03 — Sample work

Work

Real project data will appear here once it is cleared for sharing. No invented client names or results are shown in this section.

  • [Sample]

    Outer panel

    Material
    —
    Thickness
    —
    Scope
    —
    Result
    —
  • [Sample]

    Inner chassis / structural part

    Material
    —
    Thickness
    —
    Scope
    —
    Result
    —
  • [Sample]

    Bracket

    Material
    —
    Thickness
    —
    Scope
    —
    Result
    —

04 — Tools and capabilities

Simulation with finite element software, design with 3D CAD software

Part types: outer panels, inner chassis and structural parts, brackets.

Simulation

  • One-step and incremental forming analysis
  • FLD / FLC evaluation
  • Thinning, wrinkling and surface defect checks
  • Springback and compensation

Design

  • Binder and addendum design
  • Drawbead layout
  • Trim line development
  • Class-A surface corrections

Planning

  • Operation sequence
  • Transfer and progressive press compatibility
  • Die cost estimation
  • Edge crack risk assessment

05 — About

Work with someone who knows the process

Surmesh is an independent engineering service focused on the engineering of sheet metal forming dies. The approach is simple: every decision is verified by simulation, every result is reported in numbers.

FounderSur, M.Sc.

[Placeholder]

Years of experience and project count
  1. 01

    Simulation first

    Every decision is tested virtually before any die steel is cut.

  2. 02

    Reported in numbers

    Results are given as thinning, deviation and force values, not opinions.

  3. 03

    Stated assumptions

    Material card, friction and process assumptions are written out in the report.

06 — Contact

Tell us about your part

One email is enough for a quote. Including the details below makes the first reply faster.

Include in your email

  • Part type (outer panel, inner chassis / structural part, bracket)
  • Material and sheet thickness
  • Annual volume
  • Required scope (feasibility, simulation, method plan, compensation)
  • Target date, if any

You do not need to send CAD data in the first email; it can be shared after an NDA.

Quotes and projects

project@surmesh.comSend an email

General enquiries

info@surmesh.com

Turkey